15/17 Suny Jigide Street, By Celestial Way, Ogudu Lagos.
Mon-Fri 08:00 AM - 05:00 PM
Home inverters are essential for providing backup power during outages. However, inverters and battery can develop issues over time, like any other electrical device. Some problems are minor and easily fixed, while others may require professional assistance. In this guide, we’ll cover the most common inverter issues, their causes, and how to fix them effectively.
Causes:
Loose or corroded battery terminals
Old or damaged battery
Faulty charging circuit
Incorrect battery type or capacity mismatch
Solutions:
Check battery terminals: Ensure they are tightly connected and free from corrosion. Clean them with a mixture of baking soda and water if needed.
Inspect the battery condition: If the battery is old, it may need a replacement.
Check the inverter charger: If the charging circuit is faulty, get it inspected by a technician.
Ensure the right battery type: Make sure the battery is compatible with your inverter.
Causes:
Dead or weak battery
Loose or disconnected wires
Blown fuse or tripped circuit breaker
Internal component failure
Solutions:
Check the battery charge level: If the battery is fully discharged, let it charge for a few hours before testing the inverter.
Inspect the wiring: Ensure all connections are secure. Loose cables can prevent the inverter from functioning.
Replace the fuse: If the fuse is blown, replace it with a new one of the same rating.
Check for internal damage: If none of the above works, a component inside the inverter may have failed, and you should contact a professional.
Causes:
Overloaded inverter
Low battery voltage
Internal circuit failure
Solutions:
Reduce the load: Disconnect some appliances and check if the beeping stops. Overloading the inverter can cause it to sound an alarm.
Charge the battery: If the beeping is due to a low battery, allow the battery to recharge fully.
Check error codes: Some inverters display error codes along with beeping. Refer to the user manual to understand the cause.
Seek technical help: If the beeping persists, consult a technician for a detailed diagnosis.
Causes:
Excessive power consumption
Weak or failing battery
Poor battery maintenance
Incorrect battery capacity
Solutions:
Disconnect unnecessary devices: Reduce the load to extend backup time.
Check battery health: A worn-out battery won’t hold a charge for long. If your battery is older than three years, consider replacing it.
Maintain the battery properly: Regularly clean the terminals and check electrolyte levels (for lead-acid batteries).
Use the correct battery type: Ensure that the battery’s capacity (Ah rating) matches your power requirements.
Causes:
Poor ventilation around the inverter
Continuous overloading
Faulty cooling fan
High ambient temperature
Solutions:
Ensure proper airflow: Keep the inverter in a well-ventilated area, away from direct sunlight or enclosed spaces.
Reduce the load: Do not exceed the inverter’s maximum capacity.
Check the cooling fan: If the fan is not working, replace it to prevent overheating.
Monitor temperature conditions: If your inverter is in a hot environment, consider installing a fan or air conditioning to keep it cool.
Causes:
Loose internal components
Faulty fan or transformer
High-frequency electrical interference
Solutions:
Check for loose parts: Secure any internal components if possible.
Inspect the fan: A noisy fan might need cleaning or replacement.
Reduce electrical interference: Keep the inverter away from other high-power electrical devices.
Causes:
Faulty relay switch
Dead or disconnected battery
Wiring issues
Solutions:
Check the battery charge level: A fully drained battery may not allow the inverter to switch modes.
Inspect the relay switch: If the relay fails, the inverter won’t transition to battery mode. This requires professional repair.
Ensure correct wiring: Loose or incorrect wiring can cause the inverter to malfunction.
Causes:
Damaged display screen
Loose connection in the circuit board
Software glitch
Solutions:
Restart the inverter: Turn it off and back on to reset the display.
Check for loose connections: Open the display panel (if safe) and reconnect any loose wires.
Consult a technician: If the screen remains unresponsive, it may need professional repair.
Regularly clean the inverter and battery terminals to prevent dust accumulation and corrosion.
Keep the inverter in a well-ventilated area to prevent overheating.
Avoid overloading to extend the lifespan of both the inverter and the battery.
Perform regular battery maintenance by checking electrolyte levels (for lead-acid batteries) and ensuring proper charging cycles.
Schedule annual servicing with a professional to keep your inverter in top condition.
A well-maintained inverter provides reliable backup power and operates efficiently for years. Most inverter problems arise due to battery issues, overload, or poor maintenance. By following the troubleshooting steps, you can resolve common inverter problems and prolong its lifespan.
If your inverter or battery develops a complex issue beyond basic troubleshooting, don’t hesitate to contact a qualified technician for professional repair or contact Core-Power Engineers.
Call / WhatsApp (+234) 9130003339 (Office)
